Bulk Jeans: What 300, 1,000 and 3,000 Pcs Actually Cost You
Bulk jeans from 300 pcs: how the unit price falls at 1,000 and 3,000 pcs, what fabric and marker efficiency do to cost, and how AQL 2.5 inspection works.

The unit price of a jean falls in steps, not in a straight line. Cutting setup, laundry setup and inspection are fixed costs per style, so they spread across the quantity and stop mattering somewhere around 1,000 pieces.
Below is where each step happens on our floor, what fabric utilisation does to the number, and how the 25–35 day production calendar is planned around your delivery window.
Every figure here is per style per colour, because that is how the cutting ticket is written.
- 300 pcs: one cutting lay, one laundry recipe, full inspection
- 1,000 pcs: marker efficiency and laundry batching start to pay
- 3,000 pcs: fabric bought for the run, 15% off list
What changes inside the price as quantity goes up.
- 300 pcs: Setup cost per style dominates: one marker, one laundry bath, 100% inspection. List price.
- 500 pcs: 6% off: the marker is still one lay but trims and thread are bought at the next bracket.
- 1,000 pcs: 10% off: fabric is reserved from one dye lot, laundry runs two full drums instead of one partial.
- 3,000 pcs: 15% off: fabric is bought for the run, cutting is multi-layer, laundry is scheduled as a block.
- Fabric use: 1.4–1.7 m of 150 cm denim per straight-leg pair, including 4% cutting waste
- Marker efficiency: 75–82% on a five-size nest; each point gained is roughly 1.5% off the fabric cost
- Laundry: PPM (pieces per machine) 300–600 depending on the recipe; a partial drum wastes the bath
- Inspection: AQL 2.5 final inspection; third-party inspection at your cost, date shared in advance
On a 300 pc run, fabric is about 45% of the unit cost, sewing 25%, laundry 15%, hardware and trims 8%, packing and inspection 7%. The percentages shift with quantity because only the first, fourth and fifth lines are fixed per style.
At 3,000 pcs the same jean spends a larger share on fabric and a smaller share on setup, which is why a cheap fabric matters more in a big run and a cheap setup matters more in a small one.
If your target price is tight, the lever is usually the wash recipe rather than the sewing minute.
- Wash: a rinse instead of an overdye saves 6–8% of unit cost
- Fabric: 12 oz instead of 14.5 oz saves 4–6% at equal quality
- Hardware: a nylon zip instead of metal saves about 1%

Each band is a real change in how the order is cut, washed and inspected.
01 — 300 pcs
One cutting lay and one laundry recipe per style per colour: the MOQ that opens a production slot.
02 — 500 pcs
6% off the list price; the cutting setup starts to spread across the run.
03 — 1,000 pcs
10% off; cutting, laundry setup and inspection no longer dominate unit cost.
04 — 3,000 pcs
15% off; marker efficiency and fabric buying move to mill-direct quantities.
05 — Inspection and shipping
AQL 2.5, third-party inspection welcome, 25–35 days after PP approval.
Bulk inspection: who checks, and against what
Every bulk order is inspected to AQL 2.5 at final packing, which means a sample is drawn from the cartons and checked for measurement, workmanship, colour and labelling. We photograph the faults and send them with the report before the cartons are sealed.
You are welcome to appoint a third-party inspector. Give us the booking date at least five working days ahead; we will have the goods packed and staged so the inspection is not waiting on a carton line. If the inspector finds a major defect above the AQL limit, we re-work and re-inspect at our cost.
Why the 300 pc minimum exists
A single cutting lay for one style in five sizes uses about 300 pairs of fabric; below that the lay wastes width and the marker cannot nest efficiently. The laundry bath has a minimum load for an even shade. Both costs are real and both are per style, which is why the minimum is 300 pcs per style per colour rather than 300 pcs per order.
If you want to start smaller, the route is a stock fabric and a stock wash — see jeans supplier for how that is quoted, or working with a jeans manufacturer in China for the audit side.
How much cheaper is 3,000 pcs than 300 pcs?
About 15% off the list price, plus whatever you save by moving to a cheaper wash or a lighter fabric. The tier discount is on the style price; freight and sampling are separate.
Can I split a bulk order across colours?
Yes, 300 pcs per colour minimum inside the style. Three colours of 1,000 pcs each is a 3,000 pc style and earns the 15% tier, because the cutting and laundry are run per colour and scheduled as one block.
How do you keep the shade consistent across a bulk run?
Fabric is reserved from one dye lot at the mill and the laundry runs the whole order in scheduled blocks with the same recipe and the same operator team. A second dye lot is only accepted with a lab dip approved against the first.
What happens if the bulk arrives out of tolerance?
We re-work against the approved spec at our cost, or credit the affected pieces. The tolerance is written on the approved sample card, so “out of tolerance” is a measurement, not an opinion.
Can my own inspector visit during production?
Yes, at any stage. We ask for two working days' notice so the line and the samples are ready to be shown. Final inspection is booked through us or your agent, whichever you prefer.
Tell us what you want to make
Share the style, target quantity and launch date. You get fabric options, wash recommendations, a sampling date and a factory-direct quote — usually within 12 working hours.